If you have a whirlpool top load washer that is not spinning your clothes during the spin cycle, this problem could be due to a few different reasons.
These problems include a frozen pump pulley or a broken drive belt.
In many cases, the cause is easy to identify.
Here are some tips for troubleshooting the problem.
A broken drive belt
If your clothes are not spinning after washing them, there may be a broken drive belt in your Whirlpool top load washer.
To check the belt, remove the outer tub from the machine, and look underneath.
If you see debris or excessive oil, replace the clutch. If the belt is not shiny, it’s likely the drive motor has failed. If you can’t spin clothes properly, replace the drive motor.
If your top load washer is not spinning, you should check the load balance. Unbalanced loads prevent the washing machine from spinning properly and will cause the washer to shut down.
Check the drain hose for debris, too. If this is not the case, you should rebalance the load. The spinning should resume once the lid is closed.
If the problem persists, you may need to remove excess water from the machine and contact the manufacturer.
To check the drive belt, disconnect the power from your washer and remove the access panels. Locate the drive pulley wheel.
Look for damage, wear, cracks, or burning. Once you’ve located the drive pulley, you can test the motor with a multimeter to make sure it’s functioning properly. If the problem is not resolved after a few minutes, you can also try replacing the drive motor.
If your Whirlpool top load washer won’t spin clothes dry, it may have a worn or damaged drive belt. The belt must be replaced if the machine can’t spin dry clothes. Also, you may need to replace the motor coupling assembly. If this part is worn or broken, it will cause your washer to make noise and agitate during the spin cycle.
Generally, a broken drive belt is a common cause of a washing machine not spinning clothes dry. Check the door latches, drain pump, and hot and cold water valves for problems. If these aren’t the issues, the agitator might be to blame. You can remove the lid to inspect the agitator for damage and replace it.
Another common cause of this problem is a malfunctioning lid switch. The lid switch must be closed tightly to activate the washing motor. It can be easily replaced, but if you don’t have the necessary tools, a professional appliance repair person will need to check it out.
The drive belt is a critical component of the washing machine’s motor. If it’s too tight, or too loose, the basket won’t spin properly.
Another potential cause of a malfunctioning drive belt in a Whirlpool top load washer is a faulty door lock switch.
When this switch is faulty, it may not send enough electrical power to the motor to reach the appropriate spin speeds.
The washer might stop in mid-cycle and not continue spinning the clothes once the power has returned. A broken door lock switch is another possible culprit.
A Frozen pump pulley
If you are experiencing the same issue, it could be that your machine’s pump pulley has frozen. This problem can occur in both top-loading and front-loading washing machines. If the pump pulley is frozen, this will prevent the machine from spinning clothes dry.
To solve this problem, you must first check if there is anything blocking the pump pulley. You can also try re-balancing the load and re-starting the wash cycle. You may also need to drain the excess water from the machine.
If the problem persists, try a test cycle. Then, select the appropriate cycle for your machine. If you cannot spin the clothes dry, you can try manually depressing the switch. Usually, if it is depressed, the machine will spin.
If it doesn’t, you may need to replace the pump pulley. To solve this problem, you must follow the instructions provided by the manufacturer of your machine.
Another cause of the failure of the spin cycle is the drain hose. If the hose is bent, it can restrict the water from draining out. When you have a blocked drain hose, your clothes may still remain wet.
If the hose is bent, you need to disconnect it from the pump and check it for any blockages. Alternatively, you can try a different position and re-install the drain hose. If both of these solutions fail, you should replace the drain pump.
If you suspect a frozen pump pulley is the problem, you can replace it. If it does not turn freely, you can check it visually or replace the pump.
If the pulley is worn or damaged, you need to replace the pump and the drive belt. This will prevent your washer from spinning the clothes dry. This solution is a simple and cost-effective solution to the problem.
The problem can be solved by replacing the tub seal bearing. In order to do this, you need to remove the outer cabinet of your washing machine. Remove the access panel to access the drive pulley. You should then check the drive pulley nut.
The nut is sometimes loose or damaged over time. Tightening the nut will restore the washer’s ability to spin the clothes. The next step involves testing the shift actuator which controls the machine’s movement between spin and agitation.
You can check the shift actuator with a multimeter, but it is better to call a trained professional to do this.
A malfunctioning drain valve is another reason why your top load washer won’t spin the clothes. If this is the cause, you need to replace it.
The problem is not limited to top-loading machines. You can also check the drain hose for kinks or bends. If it is the cause of your washer not spinning clothes, then you should try replacing it.
A Stretched drive belt
If your Whirlpool top load washer is not spinning your clothes dry, it might be a stretched drive belt. Check the drive belt and the hose. Make sure that the hose is not clogged, kinked or not positioned correctly. If the drive belt is not stretched, replace it immediately. You should also check the lid switch. If it is malfunctioning, replace it immediately.
The main cause of this problem is a stretched drive belt. If the drive belt is stretched and not moving smoothly, you can replace it by removing the outer tub. Check the motor, drive belt, and the gearcase for visible damage. You can also check the clutch using the eyeball test. If you see any oil or debris on the gearcase, it means that the clutch is worn out.
If your washer is not spinning clothes dry, the drive belt may be stretched. To check, unplug the machine from the power and remove the control panel. Remove the drive belt and check its condition. It should be five to 10 ohms. If it doesn’t read this level, replace it immediately.
If the drive belt is stretching, check the speed of the drum. If the motor is spinning at a low speed, the drive belt may be stretched.
If your Whirlpool top load washer isn’t spinning clothes dry, check the drive belt to make sure it is not stretched. To do this, disconnect the door switch wire harness and remove the front panel.
Then, unhook the front panel from the bottom hangers. Next, remove the drum support roller. You can remove it by prying off the shaft.
You can then push the roller back into place. You can also use a triangular washer to help you hold it in place.
Whirlpool Washing Machine Problems: Summary
Unbalanced loads are another cause for a stretched drive belt. Stacking clothes may cause the washer to not spin. The weight of wet clothes is too much for it to be distributed evenly.
Also, a stretched drive belt is a sign that the drive belt is stretched.
Once you have checked these tips, you can use them to solve the problem of your washing machine.
When your whirlpool top load washer is not spinning, it could be the door lock. It should make an audible click when the door is closed. If this is the case, it may be time to replace it.
Alternatively, you might need to check the tub bearing, which is located in the center of the outer tub. This bearing allows the inner tub to spin smoothly. If the tub bearing is damaged or worn, your machine may not spin.